BluePrint Engines - GM Compatible 327 c.i. Engine - Deluxe Dressed with Polished Pulley Kit - Fuel Injected
This engine will be dyno tested before it ships to you at no additional charge (others charge $500)!
Part #: BP327CTFKV
Description
- HP & Torque: 350 HP / 350 FT LBS
- Compression Ratio: 9.45:1
- Aluminum Heads
- Hydraulic Roller Cam
- Forged Crank
- Hypereutectic Pistons
Block:
- NEW BluePrint Cast Iron Block
- 4-Bolt Main
- 4.000" Bore
- 1-Piece Rear Main Seal
- Mech fuel pump provision: Yes
- Passenger Side Dipstick
- Drilled and tapped for clutch linkage
Rotating Assembly:
- New BluePrint Forged Crankshaft
- 3.250" Stroke
- Forged 5.700" connecting rods w/ 150,000 psi bolts
- Hypereutectic pistons
- Internal Front/ External Rear
Cylinder Heads:
- BluePrint Aluminum Cylinder Heads - H8002K
- 64cc chamber
- 2.02" intake/1.60" exhaust valves
- 195cc intake/75cc exhaust runners
Cam Specs:
- Cam Type: Roller
- .495 Intake .502 Exhaust
- 220 Intake / 224 Exhaust duration
- @ .050, 114° lobe separation angle
Ignition Timing:
- 32 - 34 Degrees Total at 3500 RPM
Also Includes:
- Holley Sniper EFI System
- Premium Vintage Valve covers
- Premium Vintage Air Cleaner
- 6.75 inch Harmonic balancer
- Spark plugs
- Under Header Spark plug wires (Perfect for Rams Horn exhaust manifolds)
- Fuel Pump and feed line
- Oil pan
- Timing cover
- Aluminum Intake Manifold
- Small cap Ready to run distributor equipped with Tach Drive and coil
- Dyno tested and shipped with results
- Warranty:
- 30 month / 50,000 mile
- Front Accessory Drive with Water Pump, A/C Compressor, Alternator, and Power Steering Pump
- Warranty: 30 month / 50,000 mile
Notes:
-
Not for use in pollution-controlled vehicles.
The front accessory drive on this engine fits many vehicles, however it is the customer responsibility to accurately measure and confirm fitment. Note this is a low profile design, but things such as power steering hoses, alternator wiring, and additional fittings/fabrication may be required on some vehicles.
This engine will be dyno tested before it ships to you at no additional charge (others charge $500)!
Part #: BP327CTFKV
Description
- HP & Torque: 350 HP / 350 FT LBS
- Compression Ratio: 9.45:1
- Aluminum Heads
- Hydraulic Roller Cam
- Forged Crank
- Hypereutectic Pistons
Block:
- NEW BluePrint Cast Iron Block
- 4-Bolt Main
- 4.000" Bore
- 1-Piece Rear Main Seal
- Mech fuel pump provision: Yes
- Passenger Side Dipstick
- Drilled and tapped for clutch linkage
Rotating Assembly:
- New BluePrint Forged Crankshaft
- 3.250" Stroke
- Forged 5.700" connecting rods w/ 150,000 psi bolts
- Hypereutectic pistons
- Internal Front/ External Rear
Cylinder Heads:
- BluePrint Aluminum Cylinder Heads - H8002K
- 64cc chamber
- 2.02" intake/1.60" exhaust valves
- 195cc intake/75cc exhaust runners
Cam Specs:
- Cam Type: Roller
- .495 Intake .502 Exhaust
- 220 Intake / 224 Exhaust duration
- @ .050, 114° lobe separation angle
Ignition Timing:
- 32 - 34 Degrees Total at 3500 RPM
Also Includes:
- Holley Sniper EFI System
- Premium Vintage Valve covers
- Premium Vintage Air Cleaner
- 6.75 inch Harmonic balancer
- Spark plugs
- Under Header Spark plug wires (Perfect for Rams Horn exhaust manifolds)
- Fuel Pump and feed line
- Oil pan
- Timing cover
- Aluminum Intake Manifold
- Small cap Ready to run distributor equipped with Tach Drive and coil
- Dyno tested and shipped with results
- Warranty:
- 30 month / 50,000 mile
- Front Accessory Drive with Water Pump, A/C Compressor, Alternator, and Power Steering Pump
- Warranty: 30 month / 50,000 mile
Notes:
-
Not for use in pollution-controlled vehicles.
The front accessory drive on this engine fits many vehicles, however it is the customer responsibility to accurately measure and confirm fitment. Note this is a low profile design, but things such as power steering hoses, alternator wiring, and additional fittings/fabrication may be required on some vehicles.
Customer Reviews
Your BluePrint engine was dyno tested with the parts and specifications listed below. If you prefer to install a different part, your engine may not produce the horsepower recorded on your dyno sheet.
Part Number: BP327CTFKV
Fuel Delivery Type: Holley sniper EFI
Spark Plug: BPP7938 NGK 7938 BKR5E
Spark Plug Gap: .035"
Harmonic Balancer: BPP350 - neutral, 8" diameter
Flexplate/Flywheel: Late 350 Weighted
Stall Converter: 1800 - 2200 rpm
Intake Manifold: Dual plane, satin aluminum
Fuel Recommendation: 91 Octane
Timing (Initial/Total Advance): Initial timing - 10-16° and Total timing 32-34°
Firing Order: 1,8,4,3,6,5,7,2
Recommended Break in Oil : BPP710 (Click Here)
Recommended Service Oil : BPP10W30 (Click Here)
Recommended Oil Filter ; BPP51061 (Click Here)
Total Oil capacity with production oil pan, and Correct BPP51061 Filter : 5 Quarts
Click here to download a copy of the Installation Guide that came with your BluePrint engine.