*This engine features a polished pulley kit, note black is pictured
Description:
- Horsepower & Torque: 700 Horsepower / 640 FT LBS
- Compression Ratio: 9.5:1
- Aluminum Heads
- Hydraulic Roller Cam
- Nodular Iron Crankshaft
- Forged Pistons
Block:
- New GM Aluminum 6.2L block
- OEM Block Machined in the USA!
- 1-Piece Rear Main Seal
- 4.070" Bore
Rotating Assembly:
- Nodular Iron Crankshaft
- 3.622" Stroke
- 6.098" Forged Connecting Rods w/ 150,000 PSI Bolts
- Forged Pistons
- Internally Balanced
Cylinder Heads:
- BluePrint Aluminum Cylinder Heads -PS8015
- 72cc Chamber
- 2.165" Intake / 1.600" Exhaust Valves
- 259cc Intake / 102cc Exhaust Runners
Cam Specs:
- Cam Type: Roller Cam
- .612 Intake / .585 Exhaust
- 225 Intake / 238 Exhaust Duration
- @.050-113 Degree Lobe Separation
Ignition Timing:
- Controlled by Engine Control Module
Also Includes:
- 3.0L Whipple Supercharger
- Complete ECU, Harness, Pedal Engine Controller Kit
- Oil Pan
- Intake Manifold
- Fuel Injectors and Rail
- Coil Packs
- Spark Plugs and Wires
- Water Pump
- Harmonic Balancer
- Front Accessory Drive with Water Pump, Alternator, Power Steering Pump, and A/C Compressor
Assembled with Complete T56 Six Speed Manual Transmission Package:
Includes the following:
- McLeod Super Steel Pro Dual Disk Clutch
- Bell Housing
- Billet Flywheel
- Engine Guard
- Starter
- First Gear Ration: 2.66:1
- Second Gear Ratio: 1.78:1
- Third Gear Ration: 1.30:1
- Fourth Gear Ration: 1.00:1
- Fifth Gear Ration: 0.80:1
- Sixth Gear Ration: 0.63:1
Notes:
- BluePrint Engines Recommends Air Intake Kit BPPLS01013 to ensure correct MAF calculations and Dyno calibration are maintained with the above ECU / tuning.
- The front accessory drive on this engine fits many vehicles, however it is the customer responsibility to accurately measure and confirm fitment. Note this is a low-profile design, but things such as power steering hoses, alternator wiring, and additional fittings/fabrication may be required on some vehicles.
BETTER THAN THE REST.
The satisfaction of our customers is our highest priority at BluePrint Engines. We use quality components to balance your engine's rotating assembly within two grams of spec. We dyno test your crate engine and certify that it's ready to deliver horsepower and torque.
We give your BluePrint engine the industry's best-in-class warranty for 30-months / 50,000 miles — with the extra confidence only BluePrint can provide. Our warranty applies to individual or professional installations and is fully transferable.
For a detailed overview of our warranty, click here.
IT ALL COMES DOWN TO RESULTS.
We make sure we hit our target horsepower and proper torque with every crate engine. We use an advanced computerized balancer to get our rotating assemblies within two grams, ensuring silky smooth power over the entire RPM range. That's precisely why our engines sound and run better than our competitors.
BRAGGING RIGHTS INCLUDED!
A comprehensive, dyno-generated printout showing these critical specs will accompany your delivered engine. No more guessing or wondering what your installed engine's real-world peak horsepower and torque ratings actually are. Any doubters in the crowd? Simply flash 'em your dyno results!
This engine will be dyno tested before it ships to you at no additional charge (others charge $500)!